Internet-Draft MLRsearch March 2024
Konstantynowicz & Polak Expires 5 September 2024 [Page]
Workgroup:
Benchmarking Working Group
Internet-Draft:
draft-ietf-bmwg-mlrsearch-06
Published:
Intended Status:
Informational
Expires:
Authors:
M. Konstantynowicz
Cisco Systems
V. Polak
Cisco Systems

Multiple Loss Ratio Search

Abstract

This document proposes extensions to [RFC2544] throughput search by defining a new methodology called Multiple Loss Ratio search (MLRsearch). MLRsearch aims to minimize search duration, support multiple loss ratio searches, and enhance result repeatability and comparability.

The primary reason for extending [RFC2544] is to address the challenges and requirements presented by the evaluation and testing of software-based networking systems' data planes.

To give users more freedom, MLRsearch provides additional configuration options such as allowing multiple shorter trials per load instead of one large trial, tolerating a certain percentage of trial results with higher loss, and supporting the search for multiple goals with varying loss ratios.

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."

This Internet-Draft will expire on 5 September 2024.

Table of Contents

1. Purpose and Scope

The purpose of this document is to describe Multiple Loss Ratio search (MLRsearch), a data plane throughput search methodology optimized for software networking DUTs.

Applying vanilla [RFC2544] throughput bisection to software DUTs results in several problems:

To address the problems mentioned above, the MLRsearch library employs the following enhancements:

Some of these enhancements are formalized as MLRsearch specification, the remaining enhancements are treated as implementation details, thus achieving high comparability without limiting future improvements.

MLRsearch configuration options are flexible enough to support both conservative settings and aggressive settings. Where the conservative settings lead to results unconditionally compliant with [RFC2544], but longer search duration and worse repeatability. Conversely, aggressive settings lead to shorter search duration and better repeatability, but the results are not compliant with [RFC2544].

No part of [RFC2544] is intended to be obsoleted by this document.

2. Identified Problems

This chapter describes the problems affecting usability of various performance testing methodologies, mainly a binary search for [RFC2544] unconditionally compliant throughput.

2.1. Long Search Duration

The emergence of software DUTs, with frequent software updates and a number of different frame processing modes and configurations, has increased both the number of performance tests required to verify the DUT update and the frequency of running those tests. This makes the overall test execution time even more important than before.

The current [RFC2544] throughput definition restricts the potential for time-efficiency improvements. A more generalized throughput concept could enable further enhancements while maintaining the precision of simpler methods.

The bisection method, when unconditionally compliant with [RFC2544], is excessively slow. This is because a significant amount of time is spent on trials with loads that, in retrospect, are far from the final determined throughput.

[RFC2544] does not specify any stopping condition for throughput search, so users already have an access to a limited trade-off between search duration and achieved precision. However, each full 60-second trials doubles the precision, so not many trials can be removed without a substantial loss of precision.

2.2. DUT in SUT

[RFC2285] defines: - DUT as - The network forwarding device to which stimulus is offered and response measured [RFC2285] (section 3.1.1). - SUT as - The collective set of network devices to which stimulus is offered as a single entity and response measured [RFC2285] (section 3.1.2).

[RFC2544] specifies a test setup with an external tester stimulating the networking system, treating it either as a single DUT, or as a system of devices, an SUT.

In the case of software networking, the SUT consists of not only the DUT as a software program processing frames, but also of a server hardware and operating system functions, with server hardware resources shared across all programs and the operating system running on the same server.

Given that the SUT is a shared multi-tenant environment encompassing the DUT and other components, the DUT might inadvertently experience interference from the operating system or other software operating on the same server.

Some of this interference can be mitigated. For instance, pinning DUT program threads to specific CPU cores and isolating those cores can prevent context switching.

Despite taking all feasible precautions, some adverse effects may still impact the DUT's network performance. In this document, these effects are collectively referred to as SUT noise, even if the effects are not as unpredictable as what other engineering disciplines call noise.

DUT can also exhibit fluctuating performance itself, for reasons not related to the rest of SUT; for example due to pauses in execution as needed for internal stateful processing. In many cases this may be an expected per-design behavior, as it would be observable even in a hypothetical scenario where all sources of SUT noise are eliminated. Such behavior affects trial results in a way similar to SUT noise. As the two phenomenons are hard to distinguish, in this document the term 'noise' is used to encompass both the internal performance fluctuations of the DUT and the genuine noise of the SUT.

A simple model of SUT performance consists of an idealized noiseless performance, and additional noise effects. For a specific SUT, the noiseless performance is assumed to be constant, with all observed performance variations being attributed to noise. The impact of the noise can vary in time, sometimes wildly, even within a single trial. The noise can sometimes be negligible, but frequently it lowers the observed SUT performance as observed in trial results.

In this model, SUT does not have a single performance value, it has a spectrum. One end of the spectrum is the idealized noiseless performance value, the other end can be called a noiseful performance. In practice, trial result close to the noiseful end of the spectrum happens only rarely. The worse the performance value is, the more rarely it is seen in a trial. Therefore, the extreme noiseful end of the SUT spectrum is not observable among trial results. Also, the extreme noiseless end of the SUT spectrum is unlikely to be observable, this time because some small noise effects are likely to occur multiple times during a trial.

Unless specified otherwise, this document's focus is on the potentially observable ends of the SUT performance spectrum, as opposed to the extreme ones.

When focusing on the DUT, the benchmarking effort should ideally aim to eliminate only the SUT noise from SUT measurements. However, this is currently not feasible in practice, as there are no realistic enough models available to distinguish SUT noise from DUT fluctuations, based on the author's experience and available literature.

Assuming a well-constructed SUT, the DUT is likely its primary performance bottleneck. In this case, we can define the DUT's ideal noiseless performance as the noiseless end of the SUT performance spectrum, especially for throughput. However, other performance metrics, such as latency, may require additional considerations.

Note that by this definition, DUT noiseless performance also minimizes the impact of DUT fluctuations, as much as realistically possible for a given trial duration.

This document aims to solve the DUT in SUT problem by estimating the noiseless end of the SUT performance spectrum using a limited number of trial results.

Any improvements to the throughput search algorithm, aimed at better dealing with software networking SUT and DUT setup, should employ strategies recognizing the presence of SUT noise, allowing the discovery of (proxies for) DUT noiseless performance at different levels of sensitivity to SUT noise.

2.3. Repeatability and Comparability

[RFC2544] does not suggest to repeat throughput search. And from just one discovered throughput value, it cannot be determined how repeatable that value is. Poor repeatability then leads to poor comparability, as different benchmarking teams may obtain varying throughput values for the same SUT, exceeding the expected differences from search precision.

[RFC2544] throughput requirements (60 seconds trial and no tolerance of a single frame loss) affect the throughput results in the following way. The SUT behavior close to the noiseful end of its performance spectrum consists of rare occasions of significantly low performance, but the long trial duration makes those occasions not so rare on the trial level. Therefore, the binary search results tend to wander away from the noiseless end of SUT performance spectrum, more frequently and more widely than shorter trials would, thus causing poor throughput repeatability.

The repeatability problem can be addressed by defining a search procedure that identifies a consistent level of performance, even if it does not meet the strict definition of throughput in [RFC2544].

According to the SUT performance spectrum model, better repeatability will be at the noiseless end of the spectrum. Therefore, solutions to the DUT in SUT problem will help also with the repeatability problem.

Conversely, any alteration to [RFC2544] throughput search that improves repeatability should be considered as less dependent on the SUT noise.

An alternative option is to simply run a search multiple times, and report some statistics (e.g. average and standard deviation). This can be used for a subset of tests deemed more important, but it makes the search duration problem even more pronounced.

2.4. Throughput with Non-Zero Loss

[RFC1242] (section 3.17) defines throughput as: The maximum rate at which none of the offered frames are dropped by the device.

Then, it says: Since even the loss of one frame in a data stream can cause significant delays while waiting for the higher level protocols to time out, it is useful to know the actual maximum data rate that the device can support.

However, many benchmarking teams accept a small, non-zero loss ratio as the goal for their load search.

Motivations are many:

  • Modern protocols tolerate frame loss better, compared to the time when [RFC1242] and [RFC2544] were specified.

  • Trials nowadays send way more frames within the same duration, increasing the chance of a small SUT performance fluctuation being enough to cause frame loss.

  • Small bursts of frame loss caused by noise have otherwise smaller impact on the average frame loss ratio observed in the trial, as during other parts of the same trial the SUT may work more closely to its noiseless performance, thus perhaps lowering the trial loss ratio below the goal loss ratio value.

  • If an approximation of the SUT noise impact on the trial loss ratio is known, it can be set as the goal loss ratio.

Regardless of the validity of all similar motivations, support for non-zero loss goals makes any search algorithm more user-friendly. [RFC2544] throughput is not user-friendly in this regard.

Furthermore, allowing users to specify multiple loss ratio values, and enabling a single search to find all relevant bounds, significantly enhances the usefulness of the search algorithm.

Searching for multiple search goals also helps to describe the SUT performance spectrum better than the result of a single search goal. For example, the repeated wide gap between zero and non-zero loss loads indicates the noise has a large impact on the observed performance, which is not evident from a single goal load search procedure result.

It is easy to modify the vanilla bisection to find a lower bound for the intended load that satisfies a non-zero goal loss ratio. But it is not that obvious how to search for multiple goals at once, hence the support for multiple search goals remains a problem.

2.5. Inconsistent Trial Results

While performing throughput search by executing a sequence of measurement trials, there is a risk of encountering inconsistencies between trial results.

The plain bisection never encounters inconsistent trials. But [RFC2544] hints about the possibility of inconsistent trial results, in two places in its text. The first place is section 24, where full trial durations are required, presumably because they can be inconsistent with the results from shorter trial durations. The second place is section 26.3, where two successive zero-loss trials are recommended, presumably because after one zero-loss trial there can be a subsequent inconsistent non-zero-loss trial.

Examples include:

  • A trial at the same load (same or different trial duration) results in a different trial loss ratio.

  • A trial at a higher load (same or different trial duration) results in a smaller trial loss ratio.

Any robust throughput search algorithm needs to decide how to continue the search in the presence of such inconsistencies. Definitions of throughput in [RFC1242] and [RFC2544] are not specific enough to imply a unique way of handling such inconsistencies.

Ideally, there will be a definition of a new quantity which both generalizes throughput for non-zero-loss (and other possible repeatability enhancements), while being precise enough to force a specific way to resolve trial result inconsistencies. But until such a definition is agreed upon, the correct way to handle inconsistent trial results remains an open problem.

3. MLRsearch Specification

This chapter focuses on technical definitions needed for evaluating whether a particular test procedure adheres to MLRsearch specification.

For motivations, explanations, and other comments see other chapters.

3.1. MLRsearch Architecture

MLRsearch architecture consists of three main components: the manager, the controller, and the measurer. For definitions of the components, see the following sections.

The architecture also implies the presence of other components, such as the SUT.

These components can be seen as abstractions present in any testing procedure.

3.1.1. Measurer

The measurer is the component that performs one trial as described in [RFC2544] section 23.

Specifically, one call to the measurer accepts a trial load value and trial duration value, performs the trial, and returns the measured trial loss ratio, and optionally a different duration value.

It is the responsibility of the measurer to uphold any requirements and assumptions present in MLRsearch specification (e.g. trial forwarding ratio not being larger than one). Implementers have some freedom, for example in the way they deal with duplicated frames, or what to return if the tester sent zero frames towards SUT. Implementations are RECOMMENDED to document their behavior related to such freedoms in as detailed a way as possible.

Implementations MUST document any deviations from RFC documents, for example if the wait time around traffic is shorter than what [RFC2544] section 23 specifies.

3.1.2. Controller

The controller selects trial load and duration values to achieve the search goals in the shortest expected time.

The controller calls the measurer multiple times, receiving the trial result from each call. After exit condition is met, the controller returns the overall search results.

The controller's role in optimizing trial load and duration selection distinguishes MLRsearch algorithms from simpler search procedures.

For controller inputs, see later section Controller Inputs. For controller outputs, see later section Controller Outputs.

3.1.3. Manager

The controller gets initiated by the manager once, and subsequently calls

The manager is the component that initializes SUT, the traffic generator (tester in [RFC2544] terminology), the measurer and the controller with intended configurations. It then calls the controller once, and receives its outputs.

The manager is also responsible for creating reports in the appropriate format, based on information in controller outputs.

3.2. Units

The specification deals with physical quantities, so it is assumed each numeric value is accompanied by an appropriate physical unit.

The specification does not state which unit is appropriate, but implementations MUST make it explicit which unit is used for each value provided or received by the user.

For example, load quantities (including the conditional throughput) returned by the controller are defined to be based on a single-interface (unidirectional) loads. For bidirectional traffic, users are likely to expect bidirectional throughput quantities, so the manager is responsible for making its report clear.

3.3. SUT

As defined in [RFC2285]: The collective set of network devices to which stimulus is offered as a single entity and response measured.

3.4. Trial

A trial is the part of the test described in [RFC2544] section 23.

3.4.1. Trial Load

The trial load is the intended constant load for a trial.

Load is the quantity implied by Constant Load of [RFC1242], Data Rate of [RFC2544] and Intended Load of [RFC2285]. All three specify this value applies to one (input or output) interface.

3.4.2. Trial Duration

Trial duration is the intended duration of the traffic for a trial.

In general, this quantity does not include any preparation nor waiting described in section 23 of [RFC2544].

However, the measurer MAY return a duration value that deviates from the intended duration. This feature can be beneficial for users who wish to manage the overall search duration, rather than solely the traffic portion of it. The manager MUST report how the measurer computes the returned duration values in that case.

3.4.3. Trial Forwarding Ratio

The trial forwarding ratio is a dimensionless floating point value that ranges from 0.0 to 1.0, inclusive. It is calculated by dividing the number of frames successfully forwarded by the SUT by the total number of frames expected to be forwarded during the trial.

Note that, contrary to loads, frame counts used to compute trial forwarding ratio are aggregates over all SUT output ports.

Questions around what is the correct number of frames that should have been forwarded is outside of the scope of this document. E.g. what should the measurer return when it detects that the offered load differs significantly from the intended load.

3.4.4. Trial Loss Ratio

The trial loss ratio is equal to one minus the trial forwarding ratio.

3.4.5. Trial Forwarding Rate

The trial forwarding rate is a derived quantity, calculated by multiplying the trial load by the trial forwarding ratio.

It is important to note that while similar, this quantity is not identical to the Forwarding Rate as defined in [RFC2285] section 3.6.1, as the latter is specific to one output interface, whereas the trial forwarding ratio is based on frame counts aggregated over all SUT output interfaces.

3.5. Traffic profile

Any other specifics (besides trial load and trial duration) the measurer needs in order to perform the trial are understood as a composite called the traffic profile. All its attributes are assumed to be constant during the search, and the composite is configured on the measurer by the manager before the search starts.

The traffic profile is REQUIRED by [RFC2544] to contain some specific quantities, for example frame size. Several more specific quantities may be RECOMMENDED.

Depending on SUT configuration, e.g. when testing specific protocols, additional values need to be included in the traffic profile and in the test report. See other IETF documents.

3.6. Search Goal

The search goal is a composite consisting of several attributes, some of them are required. Implementations are free to add their own attributes.

A particular set of attribute values is called a search goal instance.

Subsections list all required attributes and one recommended attribute. Each subsection contains a short informal description, but see other chapters for more in-depth explanations.

The meaning of the attributes is formally given only by their effect on the controller output attributes (defined in later in section Search Result).

Informally, later chapters give additional intuitions and examples to the search goal attribute values. Later chapters also give motivation to formulas of computation of the outputs.

3.6.1. Goal Final Trial Duration

A threshold value for trial durations. This attribute is REQUIRED, and the value MUST be positive.

Informally, while MLRsearch is allowed to perform trials shorter than this, but results from such short trials have only limited impact on search results.

The full relation needs definitions is later subsections. But for example, the conditional throughput (definition in subsection Conditional Throughput) for this goal will be computed only from trial results from trials at least as long as this.

3.6.2. Goal Duration Sum

A threshold value for a particular sum of trial durations. This attribute is REQUIRED, and the value MUST be positive.

This uses the duration values returned by the measurer.

Informally, even when looking only at trials done at this goal's final trial duration, MLRsearch may spend up to this time measuring the same load value. If the goal duration sum is larger than the goal final trial duration, it means multiple trials need to be measured at the same load.

3.6.3. Goal Loss Ratio

A threshold value for trial loss ratios. REQUIRED attribute, MUST be non-negative and smaller than one.

Informally, if a load causes too many trials with trial loss ratios larger than this, the conditional throughput for this goal will be smaller than that load.

3.6.4. Goal Exceed Ratio

A threshold value for a particular ratio of duration sums. REQUIRED attribute, MUST be non-negative and smaller than one.

The duration sum values come from the duration values returned by the measurer.

Informally, the impact of lossy trials is controlled by this value. The full relation needs definitions is later subsections.

But for example, the definition of the conditional throughput (given later in subsection Conditional Throughput) refers to a q-value for a quantile when selecting which trial result gives the conditional throughput. The goal exceed ratio acts as the q-value to use there.

Specifically, when the goal exceed ratio is 0.5 and MLRsearch happened to use the whole goal duration sum (using full-length trials), it means the conditional throughput is the median of trial forwarding rates.

3.6.5. Goal Width

A value used as a threshold for telling when two trial load values are close enough.

RECOMMENDED attribute, positive. Implementations without this attribute MUST give the manager other ways to control the search exit condition.

Absolute load difference and relative load difference are two popular choices, but implementations may choose a different way to specify width.

Informally, this acts as a stopping condition, controlling the precision of the search. The search stops if every goal has reached its precision.

3.7. Controller Inputs

The only REQUIRED input for controller is a set of search goal instances. MLRsearch implementations MAY use additional input parameters for the controller.

The order of instances SHOULD NOT have a big impact on controller outputs, but MLRsearch implementations MAY base their behavior on the order of search goal instances.

The search goal instances SHOULD NOT be identical. MLRsearch implementation MAY allow identical instances.

3.8. Goal Result

Before defining the output of the controller, it is useful to define what the goal result is.

The goal result is a composite object consisting of several attributes. A particular set of attribute values is called a goal result instance.

Any goal result instance can be either regular or irregular. MLRsearch specification puts requirements on regular goal result instances. Any instance that does not meet the requirements is deemed irregular.

Implementations are free to define their own irregular goal results, but the manager MUST report them clearly as not regular according to this section.

All attribute values in one goal result instance are related to a single search goal instance, referred to as the given search goal.

Some of the attributes of a regular goal result instance are required, some are recommended, implementations are free to add their own.

The subsections define two required and one optional attribute for a regular goal result.

A typical irregular result is when all trials at the maximal offered load have zero loss, as the relevant upper bound does not exist in that case.

3.8.1. Relevant Upper Bound

The relevant upper bound is the smallest intended load value that is classified at the end of the search as an upper bound (see Appendix A) for the given search goal. This is a REQUIRED attribute.

Informally, this is the smallest intended load that failed to uphold all the requirements of the given search goal, mainly the goal loss ratio in combination with the goal exceed ratio.

3.8.2. Relevant Lower Bound

The relevant lower bound is the largest intended load value among those smaller than the relevant upper bound that got classified at the end of the search as a lower bound (see Appendix A) for the given search goal. This is a REQUIRED attribute.

For a regular goal result, the distance between the relevant lower bound and the relevant upper bound MUST NOT be larger than the goal width, if the implementation offers width as a goal attribute.

Informally, this is the largest intended load that managed to uphold all the requirements of the given search goal, mainly the goal loss ratio in combination with the goal exceed ratio, while not being larger than the relevant upper bound.

3.8.3. Conditional Throughput

The conditional throughput (see Appendix B) as evaluated at the relevant lower bound of the given search goal at the end of the search. This is a RECOMMENDED attribute.

Informally, this is a typical forwarding rate expected to be seen at the relevant lower bound of the given search goal. But frequently just a conservative estimate thereof, as MLRsearch implementations tend to stop gathering more data as soon as they confirm the result cannot get worse than this estimate within the goal duration sum.

3.9. Search Result

The search result is a single composite object that maps each search goal to a corresponding goal result.

In other words, search result is an unordered list of key-value pairs, where no two pairs contain equal keys. The key is a search goal instance, acting as the given search goal for the goal result instance in the value portion of the key-value pair.

The search result (as a mapping) MUST map from all the search goals present in the controller input.

3.10. Controller Outputs

The search result is the only REQUIRED output returned from the controller to the manager.

MLRsearch implementation MAY return additional data in the controller output.

4. Further Explanations

This chapter focuses on intuitions and motivations and skips over some important details.

Familiarity with the MLRsearch specification is not required here, so this chapter can act as an introduction. For example, this chapter starts talking about the tightest lower bounds before it is ready to talk about the relevant lower bound from the specification.

4.1. MLRsearch Versions

The MLRsearch algorithm has been developed in a code-first approach, a Python library has been created, debugged, and used in production before the first descriptions (even informal) were published. In fact, multiple versions of the library were used in the production over the past few years, and later code was usually not compatible with earlier descriptions.

The code in (any version of) MLRsearch library fully determines the search process (for given configuration parameters), leaving no space for deviations. MLRsearch, as a name for a broad class of possible algorithms, leaves plenty of space for future improvements, at the cost of poor comparability of results of different MLRsearch implementations.

There are two competing needs. There is the need for standardization in areas critical to comparability. There is also the need to allow flexibility for implementations to innovate and improve in other areas. This document defines the MLRsearch specification in a manner that aims to fairly balances both needs.

4.2. Exit Condition

[RFC2544] prescribes that after performing one trial at a specific offered load, the next offered load should be larger or smaller, based on frame loss.

The usual implementation uses binary search. Here a lossy trial becomes a new upper bound, a lossless trial becomes a new lower bound. The span of values between (including both) the tightest lower bound and the tightest upper bound forms an interval of possible results, and after each trial the width of that interval halves.

Usually the binary search implementation tracks only the two tightest bounds, simply calling them bounds. But the old values still B remain valid bounds, just not as tight as the new ones.

After some number of trials, the tightest lower bound becomes the throughput. [RFC2544] does not specify when (if ever) should the search stop.

MLRsearch library introduces a concept of goal width. The search stops when the distance between the tightest upper bound and the tightest lower bound is smaller than a user-configured value, called goal width from now on. In other words, the interval width at the end of the search has to be no larger than the goal width.

This goal width value therefore determines the precision of the result. As MLRsearch specification requires a particular structure of the result, the result itself does contain enough information to determine its precision, thus it is not required to report the goal width value.

This allows MLRsearch implementations to use exit conditions different from goal width.

4.3. Load Classification

MLRsearch keeps the basic logic of binary search (tracking tightest bounds, measuring at the middle), perhaps with minor technical clarifications. The algorithm chooses an intended load (as opposed to the offered load), the interval between bounds does not need to be split exactly into two equal halves, and the final reported structure specifies both bounds.

The biggest difference is that to classify a load as an upper or lower bound, MLRsearch may need more than one trial (depending on configuration options) to be performed at the same intended load.

As a consequence, even if a load already does have few trial results, it still may be classified as undecided, neither a lower bound nor an upper bound.

An explanation of the classification logic is given in the next chapter, as it relies heavily on other sections of this chapter.

For repeatability and comparability reasons, it is important that given a set of trial results, all implementations of MLRsearch classify the load equivalently.

4.4. Loss Ratios

The next difference is in the goals of the search. [RFC2544] has a single goal, based on classifying full-length trials as either lossless or lossy.

As the name suggests, MLRsearch can search for multiple goals, differing in their loss ratios. The precise definition of the goal loss ratio will be given later. The [RFC2544] throughput goal then simply becomes a zero goal loss ratio. Different goals also may have different goal widths.

A set of trial results for one specific intended load value can classify the load as an upper bound for some goals, but a lower bound for some other goals, and undecided for the rest of the goals.

Therefore, the load classification depends not only on trial results, but also on the goal. The overall search procedure becomes more complicated (compared to binary search with a single goal), but most of the complications do not affect the final result, except for one phenomenon, loss inversion.

4.5. Loss Inversion

In [RFC2544] throughput search using bisection, any load with a lossy trial becomes a hard upper bound, meaning every subsequent trial has a smaller intended load.

But in MLRsearch, a load that is classified as an upper bound for one goal may still be a lower bound for another goal, and due to the other goal MLRsearch will probably perform trials at even higher loads. What to do when all such higher load trials happen to have zero loss? Does it mean the earlier upper bound was not real? Does it mean the later lossless trials are not considered a lower bound? Surely we do not want to have an upper bound at a load smaller than a lower bound.

MLRsearch is conservative in these situations. The upper bound is considered real, and the lossless trials at higher loads are considered to be a coincidence, at least when computing the final result.

This is formalized using new notions, the relevant upper bound and the relevant lower bound. Load classification is still based just on the set of trial results at a given intended load (trials at other loads are ignored), making it possible to have a lower load classified as an upper bound, and a higher load classified as a lower bound (for the same goal). The relevant upper bound (for a goal) is the smallest load classified as an upper bound. But the relevant lower bound is not simply the largest among lower bounds. It is the largest load among loads that are lower bounds while also being smaller than the relevant upper bound.

With these definitions, the relevant lower bound is always smaller than the relevant upper bound (if both exist), and the two relevant bounds are used analogously as the two tightest bounds in the binary search. When they are less than the goal width apart, the relevant bounds are used in the output.

One consequence is that every trial result can have an impact on the search result. That means if your SUT (or your traffic generator) needs a warmup, be sure to warm it up before starting the search.

4.6. Exceed Ratio

The idea of performing multiple trials at the same load comes from a model where some trial results (those with high loss) are affected by infrequent effects, causing poor repeatability of [RFC2544] throughput results. See the discussion about noiseful and noiseless ends of the SUT performance spectrum. Stable results are closer to the noiseless end of the SUT performance spectrum, so MLRsearch may need to allow some frequency of high-loss trials to ignore the rare but big effects near the noiseful end.

MLRsearch can do such trial result filtering, but it needs a configuration option to tell it how frequent can the infrequent big loss be. This option is called the exceed ratio. It tells MLRsearch what ratio of trials (more exactly what ratio of trial seconds) can have a trial loss ratio larger than the goal loss ratio and still be classified as a lower bound. Zero exceed ratio means all trials have to have a trial loss ratio equal to or smaller than the goal loss ratio.

For explainability reasons, the RECOMMENDED value for exceed ratio is 0.5, as it simplifies some later concepts by relating them to the concept of median.

4.7. Duration Sum

When more than one trial is needed to classify a load, MLRsearch also needs something that controls the number of trials needed. Therefore, each goal also has an attribute called duration sum.

The meaning of a goal duration sum is that when a load has trials (at full trial duration, details later) whose trial durations when summed up give a value at least this long, the load is guaranteed to be classified as an upper bound or a lower bound for the goal.

As the duration sum has a big impact on the overall search duration, and [RFC2544] prescribes wait intervals around trial traffic, the MLRsearch algorithm is allowed to sum durations that are different from the actual trial traffic durations.

4.8. Short Trials

MLRsearch requires each goal to specify its final trial duration. Full-length trial is a shorter name for a trial whose intended trial duration is equal to (or longer than) the goal final trial duration.

Section 24 of [RFC2544] already anticipates possible time savings when short trials (shorter than full-length trials) are used. Full-length trials are the opposite of short trials, so they may also be called long trials.

Any MLRsearch implementation may include its own configuration options which control when and how MLRsearch chooses to use shorter trial durations.

For explainability reasons, when exceed ratio of 0.5 is used, it is recommended for the goal duration sum to be an odd multiple of the full trial durations, so conditional throughput becomes identical to a median of a particular set of forwarding rates.

The presence of shorter trial results complicates the load classification logic. Full details are given later. In short, results from short trials may cause a load to be classified as an upper bound. This may cause loss inversion, and thus lower the relevant lower bound (below what would classification say when considering full-length trials only).

For explainability reasons, it is RECOMMENDED users use such configurations that guarantee all trials have the same length. Alas, such configurations are usually not compliant with [RFC2544] requirements, or not time-saving enough.

4.9. Conditional Throughput

As testing equipment takes the intended load as an input parameter for a trial measurement, any load search algorithm needs to deal with intended load values internally.

But in the presence of goals with a non-zero loss ratio, the intended load usually does not match the user's intuition of what a throughput is. The forwarding rate (as defined in [RFC2285] section 3.6.1) is better, but it is not obvious how to generalize it for loads with multiple trial results and a non-zero goal loss ratio.

MLRsearch defines one such generalization, called the conditional throughput. It is the forwarding rate from one of the trials performed at the load in question. Specification of which trial exactly is quite technical, see the specification and Appendix B.

Conditional throughput is partially related to load classification. If a load is classified as a lower bound for a goal, the conditional throughput can be calculated, and guaranteed to show an effective loss ratio no larger than the goal loss ratio.

While the conditional throughput gives more intuitive-looking values than the relevant lower bound, especially for non-zero goal loss ratio values, the actual definition is more complicated than the definition of the relevant lower bound. In the future, other intuitive values may become popular, but they are unlikely to supersede the definition of the relevant lower bound as the most fitting value for comparability purposes, therefore the relevant lower bound remains a required attribute of the goal result structure, while the conditional throughput is only optional.

Note that comparing the best and worst case, the same relevant lower bound value may result in the conditional throughput differing up to the goal loss ratio. Therefore it is rarely needed to set the goal width (if expressed as the relative difference of loads) below the goal loss ratio. In other words, setting the goal width below the goal loss ratio may cause the conditional throughput for a larger loss ratio to become smaller than a conditional throughput for a goal with a smaller goal loss ratio, which is counter-intuitive, considering they come from the same search. Therefore it is RECOMMENDED to set the goal width to a value no smaller than the goal loss ratio.

4.10. Search Time

MLRsearch was primarily developed to reduce the time required to determine a throughput, either the [RFC2544] compliant one, or some generalization thereof. The art of achieving short search times is mainly in the smart selection of intended loads (and intended durations) for the next trial to perform.

While there is an indirect impact of the load selection on the reported values, in practice such impact tends to be small, even for SUTs with quite a broad performance spectrum.

A typical example of two approaches to load selection leading to different relevant lower bounds is when the interval is split in a very uneven way. Any implementation choosing loads very close to the current relevant lower bound is quite likely to eventually stumble upon a trial result with poor performance (due to SUT noise). For an implementation choosing loads very close to the current relevant upper bound, this is unlikely, as it examines more loads that can see a performance close to the noiseless end of the SUT performance spectrum.

However, as even splits optimize search duration at give precision, MLRsearch implementations that prioritize minimizing search time are unlikely to suffer from any such bias.

Therefore, this document remains quite vague on load selection and other optimization details, and configuration attributes related to them. Assuming users prefer libraries that achieve short overall search time, the definition of the relevant lower bound should be strict enough to ensure result repeatability and comparability between different implementations, while not restricting future implementations much.

Sadly, different implementations may exhibit their sweet spot of the best repeatability for a given search duration at different goals attribute values, especially concerning any optional goal attributes such as the initial trial duration. Thus, this document does not comment much on which configurations are good for comparability between different implementations. For comparability between different SUTs using the same implementation, refer to configurations recommended by that particular implementation.

4.11. [RFC2544] compliance

The following search goal ensures unconditional compliance with [RFC2544] throughput search procedure:

  • Goal loss ratio: zero.

  • Goal final trial duration: 60 seconds.

  • Goal duration sum: 60 seconds.

  • Goal exceed ratio: zero.

The presence of other search goals does not affect the compliance of this goal result. The relevant lower bound and the conditional throughput are in this case equal to each other, and the value is the [RFC2544] throughput.

If the 60 second quantity is replaced by a smaller quantity in both attributes, the conditional throughput is still conditionally compliant with [RFC2544] throughput.

5. Logic of Load Classification

This chapter continues with explanations, but this time more precise definitions are needed for readers to follow the explanations. The definitions here are wordy, implementers should read the specification chapter and appendices for more concise definitions.

The two related areas of focus in this chapter are load classification and the conditional throughput, starting with the latter.

The section Performance Spectrum contains definitions needed to gain insight into what conditional throughput means. The rest of the subsections discuss load classification, they do not refer to Performance Spectrum, only to a few duration sums.

For load classification, it is useful to define good and bad trials. A trial is called bad (according to a goal) if its trial loss ratio is larger than the goal loss ratio. The trial that is not bad is called good.

5.1. Performance Spectrum

There are several equivalent ways to explain the conditional throughput computation. One of the ways relies on an object called the performance spectrum. First, two heavy definitions are needed.

Take an intended load value, a trial duration value, and a finite set of trial results, all trials measured at that load value and duration value. The performance spectrum is the function that maps any non-negative real number into a sum of trial durations among all trials in the set that has that number as their forwarding rate, e.g. map to zero if no trial has that particular forwarding rate.

A related function, defined if there is at least one trial in the set, is the performance spectrum divided by the sum of the durations of all trials in the set. That function is called the performance probability function, as it satisfies all the requirements for probability mass function function of a discrete probability distribution, the one-dimensional random variable being the trial forwarding rate.

These functions are related to the SUT performance spectrum, as sampled by the trials in the set.

As for any other probability function, we can talk about percentiles of the performance probability function, including the median. The conditional throughput will be one such quantile value for a specifically chosen set of trials.

Take a set of all full-length trials performed at the relevant lower bound, sorted by decreasing forwarding rate. The sum of the durations of those trials may be less than the goal duration sum, or not. If it is less, add an imaginary trial result with zero forwarding rate, such that the new sum of durations is equal to the goal duration sum. This is the set of trials to use. The q-value for the quantile is the goal exceed ratio. If the quantile touches two trials, the larger forwarding rate (from the trial result sorted earlier) is used. The resulting quantity is the conditional throughput of the goal in question.

First example. For zero exceed ratio, when goal duration sum has been reached. The conditional throughput is the smallest forwarding rate among the trials.

Second example. For zero exceed ratio, when goal duration sum has not been reached yet. Due to the missing duration sum, the worst case may still happen, so the conditional throughput is zero. This is not reported to the user, as this load cannot become the relevant lower bound yet.

Third example. Exceed ratio 50%, goal duration sum two seconds, one trial present with the duration of one second and zero loss. The imaginary trial is added with the duration of one second and zero forwarding rate. The median would touch both trials, so the conditional throughput is the forwarding rate of the one non-imaginary trial. As that had zero loss, the value is equal to the offered load.

Note that Appendix B does not take into account short trial results.

5.1.1. Summary

While the conditional throughput is a generalization of the forwarding rate, its definition is not an obvious one.

Other than the forwarding rate, the other source of intuition is the quantile in general, and the median the the recommended case.

In future, different quantities may prove more useful, especially when applying to specific problems, but currently the conditional throughput is the recommended compromise, especially for repeatability and comparability reasons.

5.2. Single Trial Duration

When goal attributes are chosen in such a way that every trial has the same intended duration, the load classification is simpler.

The following description looks technical, but it follows the motivation of goal loss ratio, goal exceed ratio, and goal duration sum. If the sum of the durations of all trials (at the given load) is less than the goal duration sum, imagine best case scenario (all subsequent trials having zero loss) and worst case scenario (all subsequent trials having 100% loss). Here we assume there are as many subsequent trials as needed to make the sum of all trials equal to the goal duration sum. As the exceed ratio is defined just using sums of durations (number of trials does not matter), it does not matter whether the "subsequent trials" can consist of an integer number of full-length trials.

In any of the two scenarios, we can compute the load exceed ratio, As the duration sum of good trials divided by the duration sum of all trials, in both cases including the assumed trials.

If even in the best case scenario the load exceed ratio would be larger than the goal exceed ratio, the load is an upper bound. If even in the worst case scenario the load exceed ratio would not be larger than the goal exceed ratio, the load is a lower bound.

Even more specifically. Take all trials measured at a given load. The sum of the durations of all bad full-length trials is called the bad sum. The sum of the durations of all good full-length trials is called the good sum. The result of adding the bad sum plus the good sum is called the measured sum. The larger of the measured sum and the goal duration sum is called the whole sum. The whole sum minus the measured sum is called the missing sum. The optimistic exceed ratio is the bad sum divided by the whole sum. The pessimistic exceed ratio is the bad sum plus the missing sum, that divided by the whole sum. If the optimistic exceed ratio is larger than the goal exceed ratio, the load is classified as an upper bound. If the pessimistic exceed ratio is not larger than the goal exceed ratio, the load is classified as a lower bound. Else, the load is classified as undecided.

The definition of pessimistic exceed ratio is compatible with the logic in the conditional throughput computation, so in this single trial duration case, a load is a lower bound if and only if the conditional throughput effective loss ratio is not larger than the goal loss ratio. If it is larger, the load is either an upper bound or undecided.

5.3. Short Trial Scenarios

Trials with intended duration smaller than the goal final trial duration are called short trials. The motivation for load classification logic in the presence of short trials is based around a counter-factual case: What would the trial result be if a short trial has been measured as a full-length trial instead?

There are three main scenarios where human intuition guides the intended behavior of load classification.

False good scenario. The user had their reason for not configuring a shorter goal final trial duration. Perhaps SUT has buffers that may get full at longer trial durations. Perhaps SUT shows periodic decreases in performance the user does not want to be treated as noise. In any case, many good short trials may become bad full-length trials in the counter-factual case. In extreme cases, there are plenty of good short trials and no bad short trials. In this scenario, we want the load classification NOT to classify the load as a lower bound, despite the abundance of good short trials. Effectively, we want the good short trials to be ignored, so they do not contribute to comparisons with the goal duration sum.

True bad scenario. When there is a frame loss in a short trial, the counter-factual full-length trial is expected to lose at least as many frames. And in practice, bad short trials are rarely turning into good full-length trials. In extreme cases, there are no good short trials. In this scenario, we want the load classification to classify the load as an upper bound just based on the abundance of short bad trials. Effectively, we want the bad short trials to contribute to comparisons with the goal duration sum, so the load can be classified sooner.

Balanced scenario. Some SUTs are quite indifferent to trial duration. Performance probability function constructed from short trial results is likely to be similar to the performance probability function constructed from full-length trial results (perhaps with larger dispersion, but without a big impact on the median quantiles overall). For a moderate goal exceed ratio value, this may mean there are both good short trials and bad short trials. This scenario is there just to invalidate a simple heuristic of always ignoring good short trials and never ignoring bad short trials. That simple heuristic would be too biased. Yes, the short bad trials are likely to turn into full-length bad trials in the counter-factual case, but there is no information on what would the good short trials turn into. The only way to decide safely is to do more trials at full length, the same as in scenario one.

5.4. Short Trial Logic

MLRsearch picks a particular logic for load classification in the presence of short trials, but it is still RECOMMENDED to use configurations that imply no short trials, so the possible inefficiencies in that logic do not affect the result, and the result has better explainability.

With that said, the logic differs from the single trial duration case only in different definition of the bad sum. The good sum is still the sum across all good full-length trials.

Few more notions are needed for defining the new bad sum. The sum of durations of all bad full-length trials is called the bad long sum. The sum of durations of all bad short trials is called the bad short sum. The sum of durations of all good short trials is called the good short sum. One minus the goal exceed ratio is called the inceed ratio. The goal exceed ratio divided by the inceed ratio is called the exceed coefficient. The good short sum multiplied by the exceed coefficient is called the balancing sum. The bad short sum minus the balancing sum is called the excess sum. If the excess sum is negative, the bad sum is equal to the bad long sum. Otherwise, the bad sum is equal to the bad long sum plus the excess sum.

Here is how the new definition of the bad sum fares in the three scenarios, where the load is close to what would the relevant bounds be if only full-length trials were used for the search.

False good scenario. If the duration is too short, we expect to see a higher frequency of good short trials. This could lead to a negative excess sum, which has no impact, hence the load classification is given just by full-length trials. Thus, MLRsearch using too short trials has no detrimental effect on result comparability in this scenario. But also using short trials does not help with overall search duration, probably making it worse.

True bad cenario. Settings with a small exceed ratio have a small exceed coefficient, so the impact of the good short sum is small, and the bad short sum is almost wholly converted into excess sum, thus bad short trials have almost as big an impact as full-length bad trials. The same conclusion applies to moderate exceed ratio values when the good short sum is small. Thus, short trials can cause a load to get classified as an upper bound earlier, bringing time savings (while not affecting comparability).

Balanced scenario. Here excess sum is small in absolute value, as the balancing sum is expected to be similar to the bad short sum. Once again, full-length trials are needed for final load classification; but usage of short trials probably means MLRsearch needed a shorter overall search time before selecting this load for measurement, thus bringing time savings (while not affecting comparability).

Note that in presence of short trial results, the comparibility between the load classification and the conditional throughput is only partial. The conditional throughput still comes from a good long trial, but a load higher than the relevant lower bound may also compute to a good value.

5.5. Longer Trial Durations

If there are trial results with an intended duration larger than the goal trial duration, the precise definitions in Appendix A and Appendix B treat them in exactly the same way as trials with duration equal to the goal trial duration.

But in configurations with moderate (including 0.5) or small goal exceed ratio and small goal loss ratio (especially zero), bad trials with longer than goal durations may bias the search towards the lower load values, as the noiseful end of the spectrum gets a larger probability of causing the loss within the longer trials.

For some users, this is an acceptable price for increased configuration flexibility (perhaps saving time for the related goals), so implementations SHOULD allow such configurations. Still, users are encouraged to avoid such configurations by making all goals use the same final trial duration, so their results remain comparable across implementations.

6. Addressed Problems

Now when MLRsearch is clearly specified and explained, it is possible to summarize how does MLRsearch specification help with problems.

Here, "multiple trials" is a shorthand for having the goal final trial duration significantly smaller than the goal duration sum. This results in MLRsearch performing multiple trials at the same load, which may not be the case with other configurations.

6.1. Long Test Duration

As shortening the overall search duration is the main motivation of MLRsearch library development, the library implements multiple improvements on this front, both big and small.

Most of implementation details are not constrained by the MLRsearch specification, so that future implementations may keep shortening the search duration even more.

One exception is the impact of short trial results on the relevant lower bound. While motivated by human intuition, the logic is not straightforward. In practice, configurations with only one common trial duration value are capable of achieving good overal search time and result repeatability without the need to consider short trials.

6.1.1. Impact of goal attribute values

From the required goal attributes, the goal duration sum remains the best way to get even shorter searches.

Usage of multiple trials can also save time, depending on wait times around trial traffic.

The farther the goal exceed ratio is from 0.5 (towards zero or one), the less predictable the overal search duration becomes in practice.

Width parameter does not change search duration much in practice (compared to other, mainly optional goal attributes).

6.2. DUT in SUT

In practice, using multiple trials and moderate exceed ratios often improves result repeatability without increasing the overall search time, depending on the specific SUT and DUT characteristics. Benefits for separating SUT noise are less clear though, as it is not easy to distinguish SUT noise from DUT instability in general.

Conditional throughput has an intuitive meaning when described using the performance spectrum, so this is an improvement over existing simple (less configurable) search procedures.

Multiple trials can save time also when the noisy end of the preformance spectrum needs to be examined, e.g. for [RFC9004].

Under some circumstances, testing the same DUT and SUT setup with different DUT configurations can give some hints on what part of noise is SUT noise and what part is DUT performance fluctuations. In practice, both types of noise tend to be too complicated for that analysis.

MLRsearch enables users to search for multiple goals, potentially providing more insight at the cost of a longer overall search time. However, for a thorough and reliable examination of DUT-SUT interactions, it is necessary to employ additional methods beyond black-box benchmarking, such as collecting and analyzing DUT and SUT telemetry.

6.3. Repeatability and Comparability

Multiple trials improve repeatability, depending on exceed ratio.

In practice, one-second goal final trial duration with exceed ratio 0.5 is good enough for modern SUTs. However, unless smaller wait times around the traffic part of the trial are allowed, too much of overal search time would be wasted on waiting.

It is not clear whether exceed ratios higher than 0.5 are better for repeatability. The 0.5 value is still preferred due to explainability using median.

It is possible that the conditional throughput values (with non-zero goal loss ratio) are better for repeatability than the relevant lower bound values. This is especially for implementations which pick load from a small set of discrete values, as that hides small variances in relevant lower bound values other implementations may find.

Implementations focusing on shortening the overall search time are automatically forced to avoid comparability issues due to load selection, as they must prefer even splits wherever possible. But this conclusion only holds when the same goals are used. Larger adoption is needed before any further claims on comparability between MLRsearch implementations can be made.

6.4. Throughput with Non-Zero Loss

Trivially suported by the goal loss ratio attribute.

In practice, usage of non-zero loss ratio values improves the result repeatability (exactly as expected based on results from simpler search methods).

6.5. Inconsistent Trial Results

MLRsearch is conservative wherever possible. This is built into the definition of conditional throughput, and into the treatment of short trial results for load classification.

This is consistent with [RFC2544] zero loss tolerance motivation.

If the noiseless part of the SUT performance spectrum is of interest, it should be enough to set small value for the goal final trial duration, and perhaps also a large value for the goal exceed ratio.

Implementations may offer other (optional) configuration attributes to become less conservative, but currently it is not clear what impact would that have on repeatability.

7. IANA Considerations

No requests of IANA.

8. Security Considerations

Benchmarking activities as described in this memo are limited to technology characterization of a DUT/SUT using controlled stimuli in a laboratory environment, with dedicated address space and the constraints specified in the sections above.

The benchmarking network topology will be an independent test setup and MUST NOT be connected to devices that may forward the test traffic into a production network or misroute traffic to the test management network.

Further, benchmarking is performed on a "black-box" basis, relying solely on measurements observable external to the DUT/SUT.

Special capabilities SHOULD NOT exist in the DUT/SUT specifically for benchmarking purposes. Any implications for network security arising from the DUT/SUT SHOULD be identical in the lab and in production networks.

9. Acknowledgements

Some phrases and statements in this document were created with help of Mistral AI (mistral.ai).

Many thanks to Alec Hothan of the OPNFV NFVbench project for thorough review and numerous useful comments and suggestions.

Special wholehearted gratitude and thanks to the late Al Morton for his thorough reviews filled with very specific feedback and constructive guidelines. Thank you Al for the close collaboration over the years, for your continuous unwavering encouragement full of empathy and positive attitude. Al, you are dearly missed.

10. Appendix A: Load Classification

This is the specification of how to perform the load classification.

Any intended load value can be classified, according to the given search goal.

The algorithm uses (some subsets of) the set of all available trial results from trials measured at a given intended load at the end of the search. All durations are those returned by the measurer.

The block at the end of this appendix holds pseudocode which computes two values, stored in variables named optimistic and pessimistic. The pseudocode happens to be a valid Python code.

If both values are computed to be true, the load in question is classified as a lower bound according to the given search goal. If both values are false, the load is classified as an upper bound. Otherwise, the load is classified as undecided.

The pseudocode expects the following variables to hold values as follows:

The code works correctly also when there are no trial results at the given load.

balancing_sum = good_short_sum * goal_exceed_ratio / (1.0 - goal_exceed_ratio)
effective_bad_sum = bad_long_sum + max(0.0, bad_short_sum - balancing_sum)
effective_whole_sum = max(good_long_sum + effective_bad_sum, goal_duration_sum)
quantile_duration_sum = effective_whole_sum * goal_exceed_ratio
optimistic = effective_bad_sum <= quantile_duration_sum
pessimistic = (effective_whole_sum - good_long_sum) <= quantile_duration_sum

11. Appendix B: Conditional Throughput

This is the specification of how to compute conditional throughput.

Any intended load value can be used as the basis for the following computation, but only the relevant lower bound (at the end of the search) leads to the value called the conditional throughput for a given search goal.

The algorithm uses (some subsets of) the set of all available trial results from trials measured at a given intended load at the end of the search. All durations are those returned by the measurer.

The block at the end of this appendix holds pseudocode which computes a value stored as variable conditional_throughput. The pseudocode happens to be a valid Python code.

The pseudocode expects the following variables to hold values as follows:

The code works correctly only when there if there is at least one trial result measured at a given load.

all_long_sum = max(goal_duration_sum, good_long_sum + bad_long_sum)
remaining = all_long_sum * (1.0 - goal_exceed_ratio)
quantile_loss_ratio = None
for trial in long_trials:
    if quantile_loss_ratio is None or remaining > 0.0:
        quantile_loss_ratio = trial.loss_ratio
        remaining -= trial.duration
    else:
        break
else:
    if remaining > 0.0:
        quantile_loss_ratio = 1.0
conditional_throughput = intended_load * (1.0 - quantile_loss_ratio)

12. References

12.1. Normative References

[RFC1242]
Bradner, S., "Benchmarking Terminology for Network Interconnection Devices", RFC 1242, DOI 10.17487/RFC1242, , <https://www.rfc-editor.org/info/rfc1242>.
[RFC2285]
Mandeville, R., "Benchmarking Terminology for LAN Switching Devices", RFC 2285, DOI 10.17487/RFC2285, , <https://www.rfc-editor.org/info/rfc2285>.
[RFC2544]
Bradner, S. and J. McQuaid, "Benchmarking Methodology for Network Interconnect Devices", RFC 2544, DOI 10.17487/RFC2544, , <https://www.rfc-editor.org/info/rfc2544>.
[RFC9004]
Morton, A., "Updates for the Back-to-Back Frame Benchmark in RFC 2544", RFC 9004, DOI 10.17487/RFC9004, , <https://www.rfc-editor.org/info/rfc9004>.

12.2. Informative References

[FDio-CSIT-MLRsearch]
"FD.io CSIT Test Methodology - MLRsearch", , <https://csit.fd.io/cdocs/methodology/measurements/data_plane_throughput/mlr_search/>.
[PyPI-MLRsearch]
"MLRsearch 1.2.1, Python Package Index", , <https://pypi.org/project/MLRsearch/1.2.1/>.
[TST009]
"TST 009", n.d., <https://www.etsi.org/deliver/etsi_gs/NFV-TST/001_099/009/03.04.01_60/gs_NFV-TST009v030401p.pdf>.

Authors' Addresses

Maciek Konstantynowicz
Cisco Systems
Vratko Polak
Cisco Systems